How to update MB SD Connect C4 C5 FirmwareMb sd c4 plus/mb sd c5 met such error and can not communicate with car, how to solve? it seems the main unit lack the program file, and you need to update the hardware.
Here we share the procedure to update and re-flash MB SD C5/C4Plus, in case if something about firmware goes wrong you may need it.
The CAT ET Software can work for PerkinsIt will always show up in the worst place at the worst time. Like the end of a long road. That little yellow icon on the dashboard means one thing: something is wrong under your hood. Or with your gas tank. Or with one of a hundred other vehicle sensors. There are two things you can do to find out the problem: go to your dealership and do an hour’s work to find out, or get your own engine check scanner and find out the problem yourself. We choose the latter, especially if you’re still on the road.
An OBDII scanner — named for the On-Board Diagnostic II protocol used in every vehicle in the US since 1996 — taps into the secretive computer network in your Jeep. Every bit of information, from air intake temperature to water pump action, is sent over this network for the ECU to figure out and adjust as needed.
Whether you drive a Mercedes-Benz or a model from another make, you can reset the check engine light by using an appropriate scanner or by disconnecting the negative battery cable. However, if you don’t resolve the underlying issue, you’ll see the light reappear almost immediately. We’ve covered common causes and solutions below, so you can learn how to reset your check engine light with confidence.
Why is Your Engine Light On?
Here is a step-by-step guide on how to use Scania SDP3 diagnostic software to do Speed Limit setting for Scania truck.
Preparations:
Here is a quick guide on how to do a relearn on your radio if it is got a theft lock. This radio i acquired did not come like this.
How to update “Data Specialist 3+” or “USA prog / DataSmart / VAG prog”?
All our tools have the interface to help communicate with unit via USB port. If you are the DSP3+ owner then connecting your tool to PC (Windows XP/7) will open Microsoft ActiveSync application and connects to your DSP3+ automatically as to any Windows based PDA devices. If you are the USAprog / DataSmart / VAGprog owner, you need to install the “PC_link” software found on any Downloads tab under the product page that designed to communicate with your tool. The very last step for all tools is to select the Update menu and run an appropriate command such as Software Update/Active Function or any other ones.
Here is the proper solution to Xtool X100 Pad key programmer “License Exception” error when launch Xtool APP.
Error message:
Used Autel AP200 obd2 scanner to reset throttle position on a 2008 Dodge KA Nitro since the GAS pedal is electronic, it worked pretty fine!
Here is the detailed operation guide.
How to change the IP address of BMW Diagnostic Tool ENET WIFI
1.PC WIFI connect to ENET WIFI,(BMW ENET WIFI)
WIFI name：ENET_WIFI_XXXX
WIFI Password:12346578
DESCRIPTION
If your dealership purchased a new Vehicle Communication Interface (VCI) device or you would like to convert your existing VCI for using with wiTECH 2.0 System, you need to download and install the VCI Setup Utility to configure/setup your VCI for wiTECH 2.0.
Autel MaxiCOM MK908 is the next generation of MaxiSys MS908 (Global Version, No IP Limit), with ECU Coding Bi-Directional All System Diagnoses, supports full OBD diagnostic function and a lot of special functions. It’s available in multiple languages and can be changed to another language freely depends on your need. Read the guide to register and update it for your first time to use.
Autel MK908 register:
As we know, Yanhua Digimaster 3 can support automotive odometer adjustment, ECU, Airbag ECU data adjustment, computer program matching, audio decoding, automotive memory programming and key programming. Here mainly share the guide to reset Airbag and control computer data.
